系統識別號 | U0002-3009201513311600 |
---|---|
DOI | 10.6846/TKU.2015.01117 |
論文名稱(中文) | 逆熱虹吸迴路之熱傳與壓降研究 |
論文名稱(英文) | Heat transfer and Pressure drop in a Reverse Thermosyphon Loop |
第三語言論文名稱 | |
校院名稱 | 淡江大學 |
系所名稱(中文) | 機械與機電工程學系碩士班 |
系所名稱(英文) | Department of Mechanical and Electro-Mechanical Engineering |
外國學位學校名稱 | |
外國學位學院名稱 | |
外國學位研究所名稱 | |
學年度 | 103 |
學期 | 2 |
出版年 | 104 |
研究生(中文) | 林碩彥 |
研究生(英文) | Shuo-Yen Lin |
學號 | 602370669 |
學位類別 | 碩士 |
語言別 | 繁體中文 |
第二語言別 | |
口試日期 | 2015-07-15 |
論文頁數 | 41頁 |
口試委員 |
指導教授
-
康尚文
委員 - 蔡孟昌 委員 - 陳育堂 |
關鍵字(中) |
逆流熱虹吸迴路 自主向下熱傳 熱傳迴路 壓力降 |
關鍵字(英) |
Reverse thermosyphon loop Autonomous downward heat transfer Heat transfer Pressure drop |
第三語言關鍵字 | |
學科別分類 | |
中文摘要 |
逆流熱虹吸迴路發展的目的,是為了解決目前工業用熱虹吸式熱管礙於流體受熱膨脹向上流動,被迫只能配合傳統虹吸傳熱模式開發或外加機械泵迴路解決只能大量向上熱傳的瓶頸。透過蒸汽壓與重力的特殊設計,可達成自主向下循環並大量傳熱的目的,有著不須外部供電,簡單的結構和限制單方向熱流的特點。 本實驗工作流體為酒精,充填率60%,輸入功率由10W至50W,、傾斜角度及改變向下傳熱管長度1850mm、350mm。實驗在改變蒸發端容積後,於輸入功率46W、充填率60%、向下傳熱管長度350mm時,藉由觀察T6的溫度上升,證明迴路開始作動,且蓄壓槽和熱交換器僅有10度的溫度差。 |
英文摘要 |
The conventional thermosyphon in a closed system, also referred as a “bottom-heat-type” thermosyphon, depends on the natural upward movement of vapor steam, hot fluid and the downward movement of cold liquids. Nevertheless, the reverse thermosyphon loop (RTL) could not only transfer heat from a heat source near the top to a heat sink at the bottom but also transfer heat from bottom to top as a conventional thermosyphon. The self-acting downward heat transfer devices are very useful for solar heating system, ground source heat pump (GSHP), and waste heat recovery. The experiment is expected to explore the issue of different input power, tilt angle and change the downward heat transfer pipe diameters. Discussion the heat transfer and pressure drop of the reverse thermosyphon loop. |
第三語言摘要 | |
論文目次 |
目錄 中文摘要 I 英文摘要 II 目錄 III 圖目錄 V 表目錄 VII 第一章 緒論 1 1.1 研究背景 1 1.2 文獻回顧 1 1.2.1 熱虹吸管(Thermosyphon) 1 1.2.2 逆流熱虹吸迴路介紹 8 第二章 理論簡介 11 2.1 熱虹吸管簡介 11 2.2 虹吸熱管類型 11 2.3 性能分析理論 13 2.4 逆熱虹吸管原理簡介 14 第三章 實驗設計與方法 15 3.1 逆熱虹吸迴路設計及製作 17 3.1.1 設計及工作液體選擇 17 3.1.2 物質沸點與壓力關係 18 3.1.3 填充率 19 3.2 實驗步驟 19 3.3 實驗儀器 20 第四章 實驗結果與討論 24 4.1 長管實驗 24 4.1.1 燒乾測試 24 4.1.2 逐步加大瓦數測試 25 4.1.3 裝置左傾45度 26 4.2 短管實驗 28 4.2.1 裝置直立 29 4.2.2 裝置左傾30度 30 4.2.3 裝置左傾60度 32 4.2.4 裝置反轉90度 34 4.3 更改管路設計 35 4.3.1 燒乾測試 36 4.3.2 加大瓦數並增加充填量 37 4.4 結論與建議 38 參考文獻 39 圖目錄 圖1.1 熱虹吸管示意圖(工作流體為R-134a,容器材料為銅) 2 圖1.2 恆溫槽與蒸發端溫度差異 3 圖1.3 蒸發端與冷凝端溫度差對整體熱傳係數之影響 3 圖1.4 直立式環形封閉虹吸熱管示意圖 4 圖1.5 二相流迴路式虹吸熱管設計圖 5 圖1.6 二相流迴路式虹吸熱管效能圖 6 圖1.7 小型迴路熱虹吸管結構 6 圖1.8 毛細燒結結構示意圖 7 圖1.9 加熱功率100W時不同表面之蒸發熱阻 7 圖1.10 四種外加機械泵提升冷凝向下傳熱辦法 9 圖1.11藉液體相變化達到向下傳熱辦法 9 圖1.12 增加容器槽之逆熱虹吸管 10 圖1.13 增設浮閥、止回閥之逆熱虹吸管 10 圖2.1 小型迴路熱虹吸管結構 11 圖2.2 單管虹吸熱管示意圖 12 圖2.3 迴路式平行熱虹吸熱管示意圖 12 圖2.4 迴路式虹吸熱管示意圖 13 圖2.5 逆熱虹吸管示意圖 15 圖3.1 裝置之L1、L2表示圖 16 圖3.2 研究流程示意圖 17 圖3.3 設計尺寸及運作模擬圖 18 圖3.4 數據擷取器 21 圖3.5 真空幫浦 21 圖3.6 真空計 22 圖3.7 電源供應器 Chroma 62024P-80-60 22 圖3.8 恆溫水槽 23 圖3.9 流量計 23 圖4.1 熱電偶線分布示意圖 24 圖4.2 60W溫度時間圖 25 圖4.3 熱電偶線分布示意圖 27 圖4.4 長管左傾45度溫度時間圖 28 圖4.5 熱電偶線分布示意圖 29 圖4.6 短管直立溫度時間圖 30 圖4.7 5W至25W的負壓力計讀數 31 圖4.8 25W至55W的壓力計讀數 31 圖4.9 短管左傾30度溫度時間圖 32 圖4.10 5W至20W的負壓力計讀數 33 圖4.11 20W至40W的壓力計讀數 33 圖4.12 短管左傾60度溫度時間圖 34 圖4.13 反轉90度並改變止迴閥方向示意圖 35 圖4.14 短管反轉90度溫度時間圖 35 圖4.15 熱電偶線示意圖 36 圖4.16 30W溫度時間圖 37 圖4.17 46W溫度時間圖 37 表目錄 表1.1 流體與金屬材質配合表 4 表1.2 蒸發端沸騰溫度與熱通量關係 5 表4.1 60W正壓計讀數 25 表4.2 10W Chnnel1讀數 26 表4.4 20W Chnnel1讀數 26 表4.3 15W Chnnel1讀數 26 表4.5 25W Chnnel1讀數 26 表4.6 30W Chnnel1讀數 26 表4.7 正負壓力計讀數 27 |
參考文獻 |
參考文獻 [1]. E. Schmidt, in: Proc. Instn. Mech. Engrs., Conf. ASME, London, (1951), pp. 361-363. [2]. B. S. Larkin, “An experimental study of the two-phase thermosyphon tube”, 70-CSME-6(EIC-71-MECH 8) 14 (B-6). [3]. M. Shiraishi, K. Kikuchi, T. Yamanishi, “Investigation of heat transfer characteristics of a two-phase closed thermosyphon”, Heat Recovery System & CHP, 1, 1981, pp.287-297. [4]. Y. Lee, U. Mital, “A two-phase closed thermosyphon”, International Journal of Heat Mass Transfer, 15, 1972, pp.1695-1770. [5]. Y. aminaga, N. O, Ito, “Transient behavior of a thermosyphon heat pipe under stepwise temperature and heat load changes”, in: Proceedings of 7th International Heat Pipe Conference, London, 1981. [6]. I. Sauciuc, A. Akbarzadeh, P. Johnson, “Characteristics of two phase closed thermosyphon for mediua temperature heat recovery applications”, Heat Recovery Systems & CHP, 14 (7), 1995, pp.631-640. [7]. A. Faghri, M. Chen, M. Morgan, “Heat transfer characteristics in two-phase closed conventional and concentric annular thermosyphons”, Transactions of ASME Journal of Heat Mass Transfer, 111 (3), 1989, pp.611-618. [8]. F. A. Studer, T. W. McDonald, “Experimental study of a two-phase thermosyphon loop heat exchanger”, Transactions of ASHRAE, 92 (2), 1986, pp.486-493. [9]. T. Wadowski, A. Akbarzadeh, P. Johnson, “Hysteresis in thermosyphon based heat exchangers and introduction of a novel triggering system for low-temperature difference heat-recovery applications”, Heat Recovery Systems & CHP, 11 (6), 1992, pp.523-531. [10]. K. S. Ong, Md. Haider-E-Alahi, “Performance of a R-134a-filled thermosyphon”, Applied Thermal Engineering, 23, 2003, pp.2373-2381. [11]. NASA Goddard Space Flight Center, “Ammonia-Charged Aluminum Heat Pipes with Extruded Wick,” Preferred Reliability Practices, Issue PD-ED-1209, pp. 1-7, 1998. [12]. T. F. Lin, W. T. Lin, Y. L. Tsay, J. C. Wu, and R.J. Shyu, “Experimental Investigation of Geyser Boiling in an Annular Two-Phase Closed Thermosyphon”, International Journal of Heat and Mass transfer, Vol. 38, Issue 2, 1995, pp. 295-307. [13]. J. R. Hartenstine, R. W. Bonner III, J. R. Montgomery and T. Semenic, “Loop thermosyphon design for cooling of large area, high heat flux sources”, 2007 Proceedings of the ASME InterPack Conference, IPACK 2007, Vol. 1, pp. 715-722. [14]. S. W. Kang, M. C. Tsai, C. S. Hsieh, and J. Y. Chen, “Thermal Performance of a Loop Thermosyphon,” Tamkang Journal of Science and Engineering. 2009, 13(4), 281-288. [15]. T.-E. Tsai, H.-H. Wu, C.-C. Chang and S.-L. Chen, “Two-phase closed thermosyphon vapor-chamber system for electronic cooling”, International Communications in Heat and Mass Transfer, Vol. 37, Issue 5, May 2010, pp. 484-489. [16]. S. Filippeschi, On periodic two-phase thermosyphons operating against gravity, International journal of Thermal Sciences, Vol 45, 2006, pp. 124-137. [17]. Y. Dobriansky, Y. G. Yohanis, “Cyclical Reverse Thermosiphon”, Archives of thermodynamics, Vol. 31, No. 1, 2010, pp. 3-32. [18]. Y. Dobriansky, Concepts of Self-acting Circulation Loops for Downward Heat Transfer (Reverse Thermosiphons), Energy conversion and management, Vol. 52, 2011, pp.414-425. [19]. Roberts CC. A review of heat pipe liquid delivery concepts. In: Proceedings of advances in heat pipe technology conference. London: Pergamon Press, Oxford; 1982. p. 693–702 [J Heat Recov Syst 1981; 1(4): 261–6). [20]. De Beni G. Device for passive heat transport and integrated solar collector incorporating same. Euro patent 0 046 043, 31.07.81; US patent 4 467 862; UK patent 2 081 435; JP patent 57 112 658. |
論文全文使用權限 |
如有問題,歡迎洽詢!
圖書館數位資訊組 (02)2621-5656 轉 2487 或 來信