系統識別號 | U0002-2808201315190500 |
---|---|
DOI | 10.6846/TKU.2013.01201 |
論文名稱(中文) | TANA-TDQA的兩點混合近似法最佳化 探討及應用 |
論文名稱(英文) | Mixed TANA-TDQA's Two-points Approximation in Structural Engineering Optimization |
第三語言論文名稱 | |
校院名稱 | 淡江大學 |
系所名稱(中文) | 機械與機電工程學系碩士班 |
系所名稱(英文) | Department of Mechanical and Electro-Mechanical Engineering |
外國學位學校名稱 | |
外國學位學院名稱 | |
外國學位研究所名稱 | |
學年度 | 101 |
學期 | 2 |
出版年 | 102 |
研究生(中文) | 林俊毅 |
研究生(英文) | Chen-Yi Lin |
學號 | 699370556 |
學位類別 | 碩士 |
語言別 | 繁體中文 |
第二語言別 | |
口試日期 | 2013-07-09 |
論文頁數 | 131頁 |
口試委員 |
指導教授
-
史建中
委員 - 李宗翰 委員 - 吳俊瑩 |
關鍵字(中) |
近似法最佳化 混合近似函數 單調性 結構最佳化設計 |
關鍵字(英) |
Two-point approximation mixed approximation function monotonicity structural optimization engineering design |
第三語言關鍵字 | |
學科別分類 | |
中文摘要 |
最佳化結構設計都存在單調性及非單調性的行為函數。若使用近似法最佳化,為了能掌握正確性及求解效率,需要能處理單調性及非單調性的近似函數。本文建構及探討TANA-TDQA系列近似函數,稱之為 TANA3-TDQA2以及TANA1-TDQA2的兩種混合近似函數。經由數值測試確認TANA-TDQA混合近似函數比個別的TANA及TDQA近似函數的誤差小。本文詳細敘述及探討混合近似法最佳化之解題程序、參考點的選取及收斂策略。此等最佳化流程被應用在簡結構設計問題上,包含應用有限元素分析(ANSYS)及應用最佳化求解器 (Visual Doc),能以較少的有限元分析次數,提升近似法於最佳化設計的效率。以簡結構的設計經驗,應用在大型鋼結構設計最佳化,光學檢測結構設計最佳化,以及微致動器結構設計最佳化,皆可得到全域設計效果。TANA3-TDQA2的近似法最佳化為本研究最為推薦,該近似法的求解穩健性及精確性略優於TANA1-TDQA2。 |
英文摘要 |
Approximation technique can be applied for solving large scale structural optimization problems. Most structural optimization contains monotonic and non-monotonic behavior functions that seriously influences the computational efficiency. Mixed approximation method has been recognized as an effective way of dealing with this monotonicity behavior. Most published paper mentioned MMA series mixed approximation method. In this thesis, a mixed approximation function with TANA-TDQA series has be presented. The TANA approximation can well handle non-monotonic function. The TDQA can well handle monotonic function. This thesis presents two mixed approximation function TANA3-TDQA2 and TANA1-TDQA2. A numerical examples used to investigate TANA-TDQA series and also compare with individual TANA and TDQA. The error of TANA-TDQA function is generally less then individual TANA or TDQA function. Several relative simple structures are presented to illustrate how the TANA-TDQA optimization works. The finite element and analysis (ANSYS) and design optimization (Visual Doc) are integrated for solving the problem. It can be seen that the number of finite element analysis can be reduced. Three large-scale design problems are applied for further examing the performance of presenting TANA-TDQA function. The steel building structural design shows the presented approximation methods are efficient and accurate. The optical instrumental structure contain two design objectives. The micro thermal-actuator structure requires to find the maximum displacement for grasping human cell. This problem only spend about 2 hours in stead of 6 hours ,as compare with original work. TANA3-TDQA2 is the most recommended from this study, since it is more efficient than TANA1-TDQA2. |
第三語言摘要 | |
論文目次 |
致謝 I 中文摘要 II 英文摘要 III 目錄 V 圖目錄 VII 表目錄 X 符號說明 XI 第一章 緒論 1 1.1 研究動機與目的 1 1.2 研究背景 2 1.3 本文架構 5 第二章 混合近似法的理論及數學模型 6 2.1 單調與非單調的理論 6 2.2 兩點近似法 7 2.3 混合近似法 14 2.4 TANA3-TDQA2混合近似法 16 2.5 TANA1-TDQA2混合近似法 17 2.6 非單調性能的比較與討論 18 第三章 TANA-TDQA混合近似法於最佳化數值程序 29 3.1 應用TANA3-TDQA2的最佳化方法與程序 31 3.2 應用TANA1-TDQA2的最佳化方法與程序 33 3.3 TANA3-TDQA2最佳化數值解程序 34 3.4 TANA1-TDQA2最佳化數值解程序 42 第四章 TANA-TDQA混合近似法於簡結構最佳化設計 50 4.1 階梯懸臂樑結構最佳化設計 50 4.2 十桿桁架最佳化設計 63 4.3 二十五桿桁架最佳化設計 78 第五章 TANA-TDQA混合近似法於大型結構最佳化 91 5.1 鋼結構最佳化設計 91 5.2 光學檢測結構雙目標最佳化設計 105 5.3 微致動器結構最佳化設計 116 第六章 結論 126 6.1 結論 126 6.2 未來展望 127 參考文獻 128 圖目錄 圖2-1 [13] h tana3-tdqa2、tana3 及tdqa2 的相對誤差圖 20 圖 2-2 [13] h tana1 及tdqa2 的相對誤差圖 21 圖 2-3 [13] h 文獻[13]的相對誤差圖 22 圖 2-4 [13] h tana3 及tdqa2 的相對誤差圖 23 圖 2-5 [13] h tana1 及tdqa2 的相對誤差圖 23 圖 2-6 [3] h tana3-tdqa2、tana3 及tdqa2 的相對誤差圖 25 圖 2-7 [3] h tana1 及tdqa2 的相對誤差圖 25 圖 2-8 [3] h GBMMA-GMMA 及DQA-GMMA 相對誤差圖 26 圖 2-9 [3] h 文獻[3]GBMMA1 和GBMMA2 相對誤差圖 26 圖 2-10 [3] h tana3 及tdqa2 的相對誤差圖 27 圖 2-11 [3] h tana1 及tdqa2 的相對誤差圖 27 圖 3-1 TANA3-TDQA2 最佳化結果 41 圖 3-2 TANA1-TDQA2 最佳化結果 49 圖 4-1 階梯懸臂樑結構圖 50 圖 4-2 階梯懸臂樑 TANA3-TDQA2 最佳化結果 57 圖 4-3 階梯懸臂樑可行方向法目標函數迭代圖 57 圖 4-4 階梯懸臂樑 TANA1-TDQA2 最佳化結果 63 圖 4-5 十桿桁架結構及受力圖 64 圖 4-6 十桿桁架結構 TANA3-TDQA2 最佳化結果 69 圖 4-7 十桿桁架結構可行方向法目標函數迭代圖70 圖 4-8 十桿桁架結構TANA1-TDQA2 最佳化結果 77 圖 4-9 25 桿桁架結構 80 圖 4-10 25 桿桁架結構TANA3-TDQA2 最佳化結果 85 圖 4-11 25 桿桁架結構可行方向法目標函數迭代圖 85 圖 4-12 25 桿桁架結構TANA1-TDQA2 最佳化結果 89 圖 5-1 三樓二開間平面架構圖 93 圖 5-2 三樓二開間節點、樑柱中點編號圖 93 圖 5-3 (a)柱的斷面積( c A ) 、(b)樑的斷面積( b A ) 94 圖 5-4 TANA3-TDQA2 最佳化結果迭代圖 99 圖 5-5 TANA1-TDQA2 最佳化結果迭代圖 104 圖 5-6 光學檢測儀機台結構 105 圖 5-7 X-樑最佳化設計的負載及邊界條件示意圖 106 圖 5-8 X-軸樑的設計變數設定 107 圖 5-9 TANA3-TDQA2 統一目標函數迭代過程 110 圖 5-10 TANA3-TDQA2 X-樑體積迭代過程 110 圖 5-11 TANA3-TDQA2 檢測單元位移量迭代過程 111 圖 5-12 TANA1-TDQA2 統一目標函數迭代過程 114 圖 5-13 TANA1-TDQA2 X-樑體積迭代過程 114 圖 5-14 TANA1-TDQA2 檢測單元位移量迭代過程 116 圖 5-15 單臂電熱式微致動器示意圖 116 圖 5-16 TANA3-TDQA2 位移量迭代過程 121 圖 5-17 TANA1-TDQA2 位移量迭代過程 124 表目錄 表 3-1 為TANA3-TDQA2 迭代過程結果。 41 表 3-2 為TANA1-TDQA2 迭代過程結果。 48 表 4-1 TANA3-TDQA2 階梯懸臂樑迭代過程結果 56 表 4-2 TANA1-TDQA2 階梯懸臂樑迭代過程結果 62 表 4-3 TANA3-TDQA2 十桿桁架迭代過程結果 69 表 4-4 TANA1-TDQA2 十桿桁架迭代過程結果 77 表 4-5 二十五桿桁架結構兩種負載情形 80 表 4-6TANA3-TDQA2 25 桿桁架迭代過程結果 84 表 4-7 TANA1-TDQA2 25 桿桁架迭代過程結果 89 表 5-1 TANA3-TDQA2 鋼結構迭代過程結果 99 表 5-2 TANA1-TDQA2 鋼結構迭代過程結果 103 表 5-3 TANA3-TDQA2 光學檢測結構迭代過程 110 表 5-4 TANA1-TDQA2 光學檢測結構迭代過程 114 表5-5多晶矽材料性質 117 表5-6 TANA3-TDQA2單臂微致動器迭代過程 121 表5-7 TANA1-TDQA2單臂微致動器迭代過程 124 |
參考文獻 |
[1]Schmit, L. A. and Farshi, B., “Some approximation concepts for structural synthesis,” AIAA Journal, Vol.12,No.5,pp.692-699,1974. [2]Svanberg, K,“ The method of moving asymptotes – a new method for structural optimization", Int.J.Numer. Meth. Engrg. 24, pp.359–373,1987. [3] Bruyneel M., Duysinx P., and C. Fleury, “A family of MMA approximations for structural optimization”, Struct Multidisc Optim, Vol.24, pp.263-276, 2002. [4] Zhang, W. H. and Fleury, C., “A modification of convex approximation method for structural optimization”,Computer and Structures, Vol. 64,No. 1-4,pp. 89-95, 1997. [5] Zhang ,H. W., Domaszewski, M., and Fleury, C. , “A new mixed convex approximation method with application for truss configuration optimization.” Structural Optimization, pp.237~241,1998. [6]羅震,基于變密度法的連續體結構拓樸優化設計技術研究,博士 論文,華中科技大學,武漢,中國,2005 [7] Zuo ,K.T , Chen ,L.P., Zhang, Y.Q.and Yang ,J., “Study of key algorithms in topology optimization”, Int J Adv Manuf Technol, P.787–796,2007 [8] 陳俊傑,結構最佳化之新式混合兩點近似法,碩士論文,國立臺灣大學工學院機械工程學系研究所,台北,台灣,2012 [9] Fadel, G. M.,Riley, M. F. ,and Barthelemy, J. M., “Two-point exponential approximation method for structural optimization,”Structural Optimization, Vol. 2, pp. 117-124,1990. [10] Wang, L. P. and Grandhi, R.V., “Improved two-point function approximations for design optimization,” AIAA Journal, Vol. 33, No. 9,pp. 1720-1727,1995 [11] Xu, S.and Grandhi, R. V., “Effective two point function approximation for design optimization,”AIAA Journal,Vol. 36,No. 12,pp. 2269-2275,1998. [12] Kim,M.S.,Kim,J.R. ,and Jeon,J.Y.,”Efficient Mechanical System Optimization Using Two-Point Diagonal Quadratic Approximation in the Nonlinear Intervening Variable Space”, KSME International Journal. Vol. 15 No.9, pp. 1257-1267,2001 . [13] Kim, J. R. and Choi, D. H., “Enhanced two-point diagonal quadratic approximation methods,” Comput.Methods Appl.Mech. Engrg. Vol. 197,pp. 846-856 ,2008. [14] 詹景隆,進階新型三點近似法最佳化設計,碩士論文,淡江大學機械與機電工程學系研究所,台北,台灣,2009。 [15] Michalewicz,L., “GeneticAlgorithms,Numerical Optimization, and Constraints. ”, Proceedings of the Sixth International Conference on Genetic Algorithms, Morgan Kauffmanm San Mateo, pp. 151-158,1995. [16] Deb, K., “An Efficient Constraint Handling Method ForGenetic Algorithms”, Computer Methods in Applied Mechanics and Engineering, Vol. 186, pp. 331-338 , 2000. [17] 郭于鴻,兩點及三點保守近似法設計最佳化,碩士論文,淡江大學機械與機電工程學系研究所,台北,台灣,2010。 [18] 鍾金曄,加強三點近似法及光學檢測結構最佳化設計,碩士論文,淡江大學機械與機電工程學系研究所,台北,台灣,2011。 [19]Chung,T.T., Huang,Y.C. and Ma,C.H., “ Optimum Design of A High Precision AOI Machine Structure,”ICMEE, 2010 . [20]馬嘉宏,AOI機台之結構最佳化與熱補償設計,碩士論文,國立臺灣大學工學院機械工程學系研究所,台北,台灣,2010。 [21]劉惟信,機械最佳化設計,全華科技圖書股份有限公司,1996。 [22]蘇育德,可變長寬的電熱式微致動器最佳化設計,中華民國機械工程學會第二十八屆全國學術研討會論文集,C8-011,台中,台灣,2011。 [23]潘震澤,人體生理學,合記書局有限公司,台灣,2005。 [24]蘇育德,多目標技術的限制基因演算法於電熱式微致動器最佳化,碩士論文,淡江大學機械與機電工程學系研究所,台北,台灣,2011。 [25]Seyed, M. K. and Mahnaz, S., “Optimal Design Analysis of Electrothermally Driven Microactuators.”, Microsystem Techonlogies, Vol.16, No.7, pp. 1062-1071 , 2009. [26] 蔡銘山,鋼構架結構之最佳化設計,碩士論文,屏東科技大學土木系研究所,屏東,台灣,2003。 |
論文全文使用權限 |
如有問題,歡迎洽詢!
圖書館數位資訊組 (02)2621-5656 轉 2487 或 來信