系統識別號 | U0002-2301201416584400 |
---|---|
DOI | 10.6846/TKU.2014.00892 |
論文名稱(中文) | 太陽能驅動史特靈引擎之模擬研究 |
論文名稱(英文) | Simulation study of a solar concentrator operated Stirling engine |
第三語言論文名稱 | |
校院名稱 | 淡江大學 |
系所名稱(中文) | 化學工程與材料工程學系碩士班 |
系所名稱(英文) | Department of Chemical and Materials Engineering |
外國學位學校名稱 | |
外國學位學院名稱 | |
外國學位研究所名稱 | |
學年度 | 102 |
學期 | 1 |
出版年 | 103 |
研究生(中文) | 周盈秀 |
研究生(英文) | Ying-Hsiu Chou |
學號 | 601400053 |
學位類別 | 碩士 |
語言別 | 繁體中文 |
第二語言別 | |
口試日期 | 2014-01-13 |
論文頁數 | 178頁 |
口試委員 |
指導教授
-
張煖(nhchang@mail.tku.edu.tw)
委員 - 陳錫仁(hjchen@mail.tku.edu.tw) 委員 - 程學恆(shcheng@thu.edu.tw) |
關鍵字(中) |
太陽能驅動 史特靈引擎 曲柄動力模式 動態模擬 最佳化 |
關鍵字(英) |
Solar power Stirling engine Crankshaft kinematics Dynamic simulation Optimization |
第三語言關鍵字 | |
學科別分類 | |
中文摘要 |
本論文建立了Alpha 型史特靈引擎的二階數學模式與曲柄動力數學模式,以及太陽能集光碟之設計模式。利用這些模式,本論文完成了一個以氮氣為工作流體,由柴油引擎改裝之史特靈引擎的性能模擬與最佳化分析,且決定出史特靈引擎可提供給海水淡化薄膜蒸餾系統之能量。 相較於基本設計,最佳設計之篩網空隙率由0.489 調降為0.3,冷卻器長度減半,再生器通道高度減半。性能分析顯示引擎操作於0.45-3.1 MPa,工作流體溫度介於282-709 K,再生器效能達83.87%,引擎對外輸出功率為9.85 kW,熱效率為33.85%,轉動頻率為852 rpm。 集光碟之輻射接收面積約為32.4 m2。當再生器熱傳係數使用Kelly and McLand (2007)關聯式,在高輻射強度830 W/m2 且引擎工作流體之總質量分別為18.16、27.26 與36.32 g 時,引擎可輸出功率分別為7.89、8.42 與8.4 kW。中輻射強度670 W/m2 且總質量分別為27.26 與36.32 g 時,引擎可輸出功率分別為7.37 與7.4 kW。再生器熱傳係數若使用Gedeon and Wood (1996)之關聯式,在高輻射強度下且總質量分別為18.16、27.26 與36.32 g 時,引擎可輸出功率分別為7.88、8.22 與8.21 kW。中輻射強度下且總質量分別為27.26 與36.32 g 時,引擎可輸出功率分別為7.2 與7.24 kW。在低輻射強度560 W/m2,因能量太低,無法驅動引擎轉動。 |
英文摘要 |
This study has established a second order mathematical model of alpha type solar powered Stirling engine, and solar collectors of design. The study simulates a diesel engine with nitrogen as the working fluid, basic design analysis and optimal design, and the decision the Stirling engine supply the desalination membrane distillation system energy. The simulation of the optimal design case reveals the cyclic operating conditions of the working gas and the solid temperatures. For the gas, the pressure ranged 0.45-3.1 MPa, the maximum pressure difference in the engine is about 0.7 MPa and the temperature ranged 282-709 K. For the metal in the regenerator, the temperature distribution is linear and the effectiveness of the regenerator is 83.87%. The power output from the engine is 9.85 kW and the thermal efficiency is 33.85%. Rotational frequency is 852 rpm. Solar collector receives radiation area is approximately 32.4 m2. When the regenerator heat transfer coefficient using Kelly and McLand (2007) correlation in high radiation intensity 830 W/m2 and the total mass of the working fluid of the engine are 18.16,27.26 and 36.32 g, engine output power are 7.89,8.42 and 8.4 kW. The radiation intensity and the total mass of 670 W/m2, respectively 27.26 and 36.32 g, engine output power are 7.37 and 7.4 kW. If regenerator heat transfer coefficient using Gedeon and Wood (1996) the correlation at high radiation intensity and total mass are 18.16,27.26 and 36.32 g, the engine output power, respectively 7.88,8.22 and 8.21 kW. Under the radiation intensity, and the total mass are 27.26 and 36.32 g, engine output power are 7.2 and 7.24 kW. In the low radiation intensity 560 W/m2, the energy is too low to drive the engine rotation. |
第三語言摘要 | |
論文目次 |
中文摘要 I 英文摘要 II 目錄 III 圖目錄 VI 表目錄 X 第一章 緒論 1 1.1 研究背景 1 1.2 研究動機與範疇 3 1.3 論文組織與架構 4 第二章 文獻回顧 6 2.1 太陽能史特靈引擎 6 2.2 史特靈引擎系統模式 8 第三章 引擎與集光碟概念設計 12 3.1 史特靈引擎基本類型 12 3.2 史特靈引擎設計 18 3.2.1 加熱器 18 3.2.2 再生器 19 3.2.3 冷卻器 20 3.2.4 曲柄系統 21 3.3 太陽能集光碟設計 23 第四章 太陽能集光碟製作 26 4.1 裝置規格 26 4.2 太陽能集光碟製作步驟 29 第五章 單元模式建立 36 5.1 Alpha型史特靈引擎 36 5.1.1 二階數學模式 37 5.1.2 幾何尺寸與參數設定 40 5.1.3 流力與熱傳係數 43 5.1.3.1 熱對流係數 43 5.1.3.2 泛寧摩擦因子(Fanning friction factor) 44 5.1.4 工作流體物理與傳輸性質 44 5.1.5 金屬性質 46 5.1.6 模式求解 47 5.2 曲柄系統 48 5.2.1 數學模式 49 5.2.2 裝置尺寸與參數設定 54 5.2.3 模式求解 54 5.3 太陽能集光碟 55 5.3.1 數學模式 55 5.3.1.1 計算集光碟尺寸與引擎接收之能量 55 5.3.1.2 太陽之方位角和仰角 63 5.3.2 計算結果 67 5.3.2.1 引擎接收之能量 67 5.3.2.2 計算太陽之方位角和仰角 68 第六章 模式驗證 71 第七章 引擎基本設計之模擬分析 75 7.1 史特靈引擎與曲柄結合系統說明 75 7.2 工作流體狀態特性 77 7.3 金屬狀態特性 86 7.4 系統能量分析 88 7.5 關聯式比較 95 7.5.1 計算流體力學模式說明 95 7.5.2 結果比較 97 第八章 引擎設計與操作敏感度分析 102 8.1 工作流體 105 8.2 熱交換器幾何參數 106 8.2.1 加熱器尺寸 106 8.2.1.1 加熱器長度 106 8.2.1.2 加熱器通道截面積 107 8.2.2 冷卻器尺寸 109 8.2.2.1 冷卻器長度 109 8.2.2.2 冷卻器通道截面積 110 8.2.3 再生器尺寸 112 8.2.3.1 再生器長度 112 8.2.3.2 再生器流體通道截面積 113 8.2.3.3 再生器篩網空隙率 114 8.2.3.4 篩網金屬比熱 115 8.2.4 熱對流係數 117 8.2.4.1 加熱器流體 117 8.2.4.2 冷卻器流體 118 8.2.4.3 加熱器與冷卻器流體 119 8.2.5 曲柄系統尺寸 121 8.3 操作條件 123 8.3.1 工作流體總質量 123 8.3.2 冷卻器壁溫 124 8.3.3 加熱器壁溫 125 8.4 含曲柄系統分析 127 8.4.1 加熱器熱通量 127 8.4.2 加熱器通道截面積85% 130 8.4.3 冷卻器通道截面積85% 131 8.4.4 冷卻器長度50% 132 8.4.5 再生器通道截面積50% 133 8.4.6 再生器長度125% 134 8.4.7 再生器篩網空隙率0.3 135 第九章 引擎最佳設計之模擬分析 136 9.1 裝置尺寸與操作條件 136 9.2 工作流體狀態特性 139 9.3 金屬狀態特性 148 9.4 系統能量分析 150 9.5 供應海水淡化薄膜蒸餾系統之能量分析 157 第十章 結論與建議 167 符號說明 170 參考文獻 174 圖目錄 圖1.2 集光型太陽能史特靈引擎電力系統 3 圖2.1史特靈引擎之PV與TS圖 8 圖3.1 α型史特靈引擎之結構 13 圖3.2 α型史特靈引擎之作動 14 圖3.3 β型史特靈引擎之結構 15 圖3.4 β型史特靈引擎之作動 15 圖3.5 γ型史特靈引擎之結構 16 圖3.6 γ型史特靈引擎之作動 17 圖3.7加熱器內部結構 19 圖3.8 再生器內部結構 20 圖3.9 冷卻器內部結構 21 圖3.10 曲柄結構 22 圖3.11 複鏡式集光碟與光線之示意圖 23 圖3.12 複式鏡集光碟座標示意圖 25 圖4.1 太陽能集光碟之座標系統與檢驗光線 28 圖4.2 主鏡模具與基板 29 圖4.3 玻璃纖維布 31 圖4.4 次鏡示意圖 32 圖4.5 次鏡反射鏡膜裁切方式 33 圖4.6 主鏡反射鏡膜裁切方式 33 圖4.7 集光碟支架系統 34 圖4.8 主體承載支架側視圖 35 圖4.9 主體承載支架後視圖 35 圖5.1 Alpha型史特靈引擎示意圖 37 圖5.2 篩網示意圖 40 圖5.3 曲柄系統 48 圖5.4 活塞受力 51 圖5.5連接桿受力 52 圖5.6 曲柄軸受力 53 圖5.7 複式鏡集光碟曲面計算示意圖 59 圖5.8 次鏡聚焦點之偏差 60 圖5.9 兩鏡距離之計算示意圖 60 圖5.10 複鏡式集光碟輻射量計算示意圖 62 圖5.11 座標系統轉換 63 圖5.12 太陽之座標位置示意圖 65 圖5.13 淡水地區每月最大輻射量 67 圖5.14 淡水地區每月每時之太陽方位角 69 圖5.15 淡水地區每月每時之太陽仰角 69 圖6.1 GPU-3引擎之熱通量分佈 73 圖6.2 GPU-3引擎之壓降能耗分佈 74 圖7.1史特靈引擎與曲柄結合系統 76 圖7.2 基本設計工作流體體積之循環變化 78 圖7.3 基本設計工作流體壓力之循環變化 78 圖7.4 基本設計膨脹空間與壓縮空間壓力之循環變化 79 圖7.5 基本設計工作流體壓力差之循環變化 79 圖7.6 基本設計工作流體質量之循環變化 80 圖7.7 基本設計工作流體質量流率之循環變化 81 圖7.8 基本設計工作流體雷諾數之循環變化 81 圖7.9 基本設計系統內氣體粒子運動軌跡 82 圖7.10 基本設計工作流體溫度之循環變化 83 圖7.11 基本設計冷側工作流體與冷卻流體出口溫度之循環變化 84 圖7.12 基本設計再生器工作流體溫度之循環變化 84 圖7.13 基本設計熱側工作流體溫度之循環變化 85 圖7.14 基本設計工作流體溫度差分佈 85 圖7.15 基本設計系統內部金屬溫度之循環變化 86 圖7.16 基本設計系統內部金屬溫度差分佈 87 圖7.17 基本設計工作流體熱通量與活塞作功之循環變化 88 圖7.18 基本設計系統週期累積能量 89 圖7.19 基本設計曲柄力矩之循環變化 90 圖7.20 基本設計曲柄與飛輪之週期累積功 90 圖7.21 基本設計模擬過程引擎轉速變化 91 圖7.22 基本設計穩定運轉之曲柄轉速變化 91 圖7.23 基本設計膨脹空間與壓縮空間壓力與體積關係 92 圖7.24 基本設計整體系統壓力與體積關係 92 圖7.25 基本設計系統能量平衡 93 圖7.26 基本個案之摩擦因子變化 99 圖7.27 CFD回歸關聯式個案之摩擦因子變化 99 圖7.28 CFD回歸關聯式個案之摩擦因子變化(放大y軸刻度) 100 圖7.29 基本個案之熱傳係數變化 101 圖7.30 CFD回歸關聯式個案之熱傳係數變化 101 圖8.1 加熱器通道截面積對系統效率之影響 108 圖8.2 加熱器通道截面積對平均熱通量之影響 108 圖8.3加熱器長度對系統效率之影響 108 圖8.4 加熱器長度對平均熱通量之影響 108 圖8.5 冷卻器通道截面積對系統效率之影響 111 圖8.6 冷卻器通道截面積對平均熱通量之影響 111 圖8.7 冷卻器長度對系統效率之影響 111 圖8.8 冷卻器長度對平均熱通量之影響 111 圖8.9再生器長度對系統效率之影響 116 圖8.10 再生器長度對平均熱通量之影響 116 圖8.11再生器通道截面積對系統效率之影響 116 圖8.12 再生器通道截面積對平均熱通量之影響 116 圖8.13 再生器篩網空隙率對系統效率之影響 116 圖8.14 再生器篩網空隙率對平均熱通量之影響 116 圖8.15 篩網金屬比熱對系統效率之影響 116 圖8.16 篩網金屬比熱對平均熱通量之影響 116 圖8.17 加熱器熱傳係數對系統效率之影響 120 圖8.18 加熱器熱傳係數對平均熱通量之影響 120 圖8.19 冷卻器熱傳係數對系統效率之影響 120 圖8.20 冷卻器熱傳係數對平均熱通量之影響 120 圖8.21 加熱器與冷卻器熱傳係數對系統效率之影響 120 圖8.22 加熱器與冷卻器熱傳係數對平均熱通量之影響 120 圖8.23 曲柄尺寸對系統效率之影響 122 圖8.24 曲柄尺寸對平均熱通量與轉動頻率之影響 122 圖8.25 氣體總質量對系統效率之影響 126 圖8.26 氣體總質量對平均熱通量之影響 126 圖8.27 冷卻器壁溫對系統效率之影響 126 圖8.28 冷卻器壁溫對平均熱通量之影響 126 圖8.29 加熱器壁溫對系統效率之影響 126 圖8.30加熱器壁溫對平均熱通量之影響 126 圖8.31 加熱器熱通量對效率之影響 128 圖8.32 加熱器熱通量對轉速之影響 128 圖9.1 最佳設計工作流體體積之循環變化 140 圖9.2 最佳設計工作流體壓力之循環變化 140 圖9.3 最佳設計膨脹空間與壓縮空間壓力之循環變化 141 圖9.4 最佳設計工作流體壓力差之循環變化 141 圖9.5 最佳設計工作流體質量之循環變化 142 圖9.6 最佳設計工作流體質量流率之循環變化 143 圖9.7 最佳設計工作流體雷諾數之循環變化 143 圖9.8 最佳設計系統內氣體粒子運動軌跡 144 圖9.9 最佳設計工作流體溫度之循環變化 145 圖9.10 最佳設計冷側工作流體與冷卻流體出口溫度之循環變化 146 圖9.11 最佳設計再生器工作流體溫度之循環變化 146 圖9.12 最佳設計熱側工作流體溫度之循環變化 147 圖9.13 最佳設計工作流體溫度差分佈 148 圖9.14 最佳設計系統內部金屬溫度之循環變化 149 圖9.15 最佳設計系統內部金屬溫度差分佈 149 圖9.16 最佳設計工作流體熱通量與活塞作功之循環變化 150 圖9.17 最佳設計系統週期累積能量 151 圖9.18 最佳設計曲柄力矩之循環變化 152 圖9.19 最佳設計曲柄與飛輪之週期累積功 152 圖9.20 最佳設計模擬過程引擎轉速變化 153 圖9.21 最佳設計穩定運轉之曲柄轉速變化 153 圖9.22 最佳設計膨脹空間與壓縮空間壓力與體積關係 154 圖9.23 最佳設計整體系統壓力與體積關係 154 圖9.24 最佳設計系統能量平衡 156 圖9.25 熱通量與質量對效率之影響(Kelly and McLand (2007)) 160 圖9.26 熱通量與質量對輸出功率之影響(Kelly and McLand (2007)) 160 圖9.27 熱通量與質量對效率之影響(Gedeon and Wood (1996)) 160 圖9.28 熱通量與質量對輸出功率之影響(Gedeon and Wood (1996)) 160 表目錄 表3.1 不同類型之史特靈引擎特性 17 表3.2 集光碟裝置資料 24 表4.1 小尺寸集光碟裝置資料 27 表4.2 樹脂與硬化劑之物性資料 30 表4.3 3M-1100反射鏡膜之物性資料 33 表5.1 Alpha型史特靈引擎模式 38 表5.2 篩網裝置計算 41 表5.3 史特靈引擎之基本設計裝置尺寸 41 表5.4 曲柄系統之裝置尺寸 54 表5.5 複鏡式集光碟裝置尺寸分析所需參數 61 表5.6 太陽座標位置之計算方程式 66 表5.7 不同輻射程度下,引擎可接收之能量 68 表5.8 太陽位置之計算結果 70 表6.1 GPU-3引擎之實驗與模擬結果 72 表7.1 基本設計系統性能結果 94 表7.2 計算流體力學模擬所回歸之關聯式 96 表7.3 基本設計使用不同關聯式之模擬性能比較 98 表8.1 基本個案之操作條件與初始狀態 103 表8.2 基本個案含與不含曲柄系統之模擬結果比較 103 表8.3 敏感度分析之參數範圍 104 表8.4 改變工作流體種類之系統性能結果 105 表8.5 改變加熱器長度之系統性能結果 106 表8.6 改變加熱器通道截面積之系統性能結果 107 表8.7 改變冷卻器長度之系統性能結果 109 表8.8 改變冷卻器通道截面積之系統性能結果 110 表8.9 改變再生器長度之系統性能結果 112 表8.10 改變再生器通道截面積之系統性能結果 113 表8.11 改變再生器篩網空隙率之系統性能結果 114 表8.12 改變再生器篩網比熱之系統性能結果 115 表8.13 改變加熱器流體熱傳係數之系統性能結果 117 表8.14 改變冷卻器流體熱傳係數之系統性能結果 118 表8.15 改變加熱器與冷卻器流體熱傳係數之系統性能結果 119 表8.16 改變曲柄系統尺寸之系統性能結果 122 表8.17 改變氣體總質量之系統性能結果 123 表8.18 改變冷卻器壁溫之系統性能結果 124 表8.19 改變加熱器壁溫之系統性能結果 125 表8.20改變加熱器熱通量之系統性能結果 129 表8.21 加熱器通道截面積調降為85%之系統性能 130 表8.22 冷卻器通道截面積調降為85%之系統性能 131 表8.23 冷卻器長度調降為50%之系統性能 132 表8.24 再生器通道截面積調降為50%之系統性能 133 表8.25 再生器長度調整為125%之系統性能 134 表8.26 曲柄系統改變再生器篩網空隙度之系統性能結果 135 表9.1 引擎基本與最佳設計之熱交換器規格 137 表9.2 引擎最佳設計各單元之規格 138 表9.3 最佳設計系統性能結果 156 表9.4 輸出功率對質量與熱通量回歸式之參數 159 表9.5 最佳設計系統性能結果(再生器關聯式Kelly and McLand (2007),總質量18.16g) 161 表9.6 最佳設計系統性能結果(再生器關聯式Kelly and McLand (2007),總質量27.26g) 162 表9.7 最佳設計系統性能結果(再生器關聯式Kelly and McLand (2007),總質量36.32g) 163 表9.8 最佳設計系統性能結果(再生器關聯式Gedeon and Wood (1996),總質量18.16g) 164 表9.9 最佳設計系統性能結果(再生器關聯式Gedeon and Wood (1996),總質量27.26g) 165 表9.10 最佳設計系統性能結果(再生器關聯式Gedeon and Wood (1996),總質量36.32g) 166 |
參考文獻 |
Ahmed, A., Al-Agami, M., Al-Garni, M., “Solar powered Stirling engine with a single membrane dish concentrator,” Proceedings of the First World Renewable Energy Congress, Energy and the Environment, Reading, UK, vol. 2, pp.1202-1207, 1990. Altfeld, K., Leiner, W., Fiebig, M., “Second law optimization of flat-plate solar air heaters Part I: The concept of net exergy flow and the modeling of solar air heaters,” Solar Energy, vol. 41, no. 2, pp. 127-132, 1988a. Altfeld, K., Leiner, W., Fiebig, M., “Second law optimization of flat-plate solar air heaters. Part 2: Results of optimization and analysis of sensibility to variations of operating conditions,” Solar Energy, vol. 41, no. 4, pp. 309-317, 1988b. Chen, N., Griffin, F., “Review of Stirling-engine mathematical models,” Oak Ridge National Laboratory Report, ORNL/CON-135, 1983. Chen, N., Griffin, F., West, C., “Linear harmonic analysis of Stirling engine thermodynamics,” Oak Ridge National Laboratory Report, ORNL/CON-155, 1984. Cheng, C., Yu, Y., “Dynamic simulation of a beta-type Stirling engine with cam-drive mechanism via the combination of the thermodynamic and dynamic models,” Renewable Energy, vol. 36, no. 2, pp. 714-725, 2011. Colebrook, C.F., “Turbulent flow in pipes, with particular reference to the transition region between the smooth and rough pipe laws,” Journal of the ICE, vol. 11, no. 4, pp. 133-156, 1939. Costea, M., Petrescu, S., Harman, C., “The effect of irreversibilities on solar Stirling engine cycle performance,” Energy Conversion and Management, vol. 40, no. 15, pp. 1723-1731, 1999. Daniels, F., Direct use of the sun's energy, Yale University Press, 1964. Dittus, F., Boelter, L., “Heat transfer in automobile radiators of the tubular type,” University of California Publications in Engineering, vol. 2, pp. 43, 1930. Dyson, R.W., Wilson, S.D., Tew, R.C., “Review of computational Stirling analysis methods,” Collection of Technical Papers, International Energy Conversion Engineering Conference, pp. 511, 2004. Dyson, R.W., Wilson, S.D., Tew, R.C., Demko, R., On the need for multidimensional Stirling simulations, National Aeronautics and Space Administration, Glenn Research Center, USA, 2005. Eldighidy, S.M., “Optimum outlet temperature of solar collector for maximum work output for an Otto air-standard cycle with ideal regeneration,” Solar Energy, vol. 51, no. 3, pp. 175-182, 1993. Garcia, F.J., Perez, M.A.S., Ruiz-Hernandez, V., “Thermal model of the EuroDish solar Stirling engine,” Journal of Solar Energy Engineering, vol. 130, pp. 011014-011011, 2008. Gear, C.W., Numerical initial value problems in ordinary differential equations, Prentice Hall, New York, USA, 1971. Gedeon, D., Wood, J., Oscillating-flow regenerator test rig: Hardware and theory with derived correlations for screens and felts, NASA, 1996. Hamaguchi, K., Takahashi, S., Miyabe, H., Heat transfer characteristics of regenerator matrix (case of packed wire gauzes), NASA STI/Recon Technical Report, vol. 84, pp. 34693, 1984. He, M., Sanders, S., “Design of a 2.5 kw low temperature Stirling engine for distributed solar thermal generation,” 9th Annual International Energy Conversion Engineering Conference, pp. 7, 2011. Howell, J.R., Bannerot, R.B., “Optimum solar collector operation for maximizing cycle work output,” Solar Energy, vol. 19, no. 2, pp. 149-153, 1977. Incropera, F.P., DeWitt, D.P., Fundamentals of heat and mass transfer, 6th Ed., John Wiley & Sons, New York, USA, 2007. Karabulut, H., Yucesu, H.S., Cınar, C., Aksoy, F., “An experimental study on the development of a β-type Stirling engine for low and moderate temperature heat sources,” Applied Energy, vol. 86, no. 1, pp. 68-73, 2009. Kays, W.M., Crawford, M.E., Weigand, B., Convective heat and mass transfer, McGraw-Hill, New York, USA, 1993. Kongtragool, B., Wongwises, S., “A review of solar-powered Stirling engines and low temperature differential Stirling engines,” Renewable and Sustainable Energy Reviews, vol. 7, no. 2, pp. 131-154, 2003. Mancini, T., Heller, P., Butler, B., Osborn, B., Schiel, W., Goldberg, V., Buck, R., Diver, R., Andraka, C., Moreno, J., “Dish-Stirling Systems: An Overview of Development and Status,” Journal of Solar Energy Engineering, vol. 125, pp. 135, 2003. Martini, W.R., Stirling engine design manual, 1978. Palacin F., Alonso S., Bravo Y., Monne C., “Improvement options in the dish Stirling technology,” 30th ISES Biennial Solar World Congress 2011, vol. 5, pp.3870-3877, 2011. Powell, R., Ho, C.Y., Liley, P.E., Thermal conductivity of selected materials, Washington, U.S. Dept. of Commerce, National Bureau of Standards, 1966. Rajbarkohan, M., Rasekh, M., Hosani, A.H., Asadi, M.R., “Kinamtics and kinetic analysis of slider crank mechanism in otto linear four cylinder Z24 engine,” Journal of Mechanical Engineerin Reasearch, vol. 3, no. 3, pp. 85-95, 2011. Reinalter, W., Ulmer, S., Heller, P., Rauch, T., Gineste, J., Ferriere, A., Nepveu, F., “Detailed performance analysis of the 10 kW CNRS-PROMES dish/Stirling system,” Proceedings of the 13th Solar PACES International Symposium, 2006. Rizzo, J.G., The Stirling Engine Manual: one quart common sense, one quart ingenuity, one quart good workmanship and one quart pot luck, Camden Miniature steam services, 1999. Sandia, Stirling energy systems set new world record of 31.25% for solar-to-grid conversion efficiency, http://thefraserdomain.typepad.com/energy/ 2008/02/sandia-stirling.html. Schlaich bergermann und partner, Parabolic troughs, http://www.sbp.de. Schock, A., “Stirling engine nodal analysis program,” Journal of Energy, vol. 2, no. 6, pp. 354-362, 1978. Schock, A., “Stirling engine nodal analysis program,” Journal of Energy, vol. 2, no. 6, pp. 354-362, 1978. Shendage, D., Kedare, S., Bapat, S., “An analysis of beta type Stirling engine with rhombic drive mechanism,” Renewable Energy, vol. 36, no. 1, pp. 289-297, 2011. Smith, P.D., Practical astronomy with your calculator, Cambridge University Press, 1981. Snyman, H., Harms, T., Strauss, J., “Design analysis methods for Stirling engines,” Journal of Energy in Southern Africa, vol. 19, no. 3, pp. 4-19, 2008. Stine, W.B., Diver, R.B., A compendium of solar dish/Stirling technology, Sandia National Laboratories, Albuquerque, Report SAND93-7026 UC-236, 1994. Tarfaoui, M., Akesbi, S., “A finite element model of mechanical properties of plain weave,” Colloids and Surfaces A: Physicochemical and Engineering Aspects, vol. 187, pp. 439-448, 2001. Tew, R.C., Jefferies, K. & Miao, D., A Stirling engine computer model for performance calculations, Department of Energy, Office of Conservation and Solar Applications, Division of Transportation Energy Conservation, 1978. Tew, R., Ibrahim, M., Danila, D., Simon, T., Mantell, S., Sun, L., Gedeon, D., Kelly, K., McLean, J., Wood, G., A microfabricated involute-foil regenerator for Stirling engines, NASA/TM-2007-215006, 2007. Thombare, D., Verma, S., “Technological development in the Stirling cycle engines,” Renewable and Sustainable Energy Reviews, vol. 12, no. 1, pp. 1-38, 2008. Timoumi, Y., Tlili, I., Ben Nasrallah, S., “Design and performance optimization of GPU-3 Stirling engines,” Energy, vol. 33, no. 7, pp. 1100-1114, 2008. Vinogradov, O., Fundamentals of Kinematics and Dynamics of Machines and Mechanisms, CRC Press LLC, Florida, USA, 2000. Walker, G., Stirling engines, Oxford University Press, New York, USA, 1980. WB, S., “Stirling engines,” The CRC Handbook of Mechanical Engineers, CRC Press, 1998. West, C.D., Principles and applications of Stirling engines, Van Nostrand Reinhold New York, USA, 1986. 沈仲晃, “太陽能電池安裝角度與電能輸出之研究,” Journal of Technology, vol. 20, no. 1, pp. 15-20, 2005. |
論文全文使用權限 |
如有問題,歡迎洽詢!
圖書館數位資訊組 (02)2621-5656 轉 2487 或 來信