§ 瀏覽學位論文書目資料
  
系統識別號 U0002-1807201113483000
DOI 10.6846/TKU.2011.00649
論文名稱(中文) 具外罩及扭轉葉片之小型水平式風力發電機空氣動力特性探討
論文名稱(英文) Studies of aerodynamic characteristics of twist blades on small horizontal-axis wind turbines with shroud
第三語言論文名稱
校院名稱 淡江大學
系所名稱(中文) 航空太空工程學系碩士班
系所名稱(英文) Department of Aerospace Engineering
外國學位學校名稱
外國學位學院名稱
外國學位研究所名稱
學年度 99
學期 2
出版年 100
研究生(中文) 鄭健成
研究生(英文) Chien-Chen Cheng
學號 698430138
學位類別 碩士
語言別 繁體中文
第二語言別
口試日期 2011-06-27
論文頁數 95頁
口試委員 指導教授 - 陳增源
委員 - 陳增源
委員 - 管衍德
委員 - 陳慶祥
關鍵字(中) 水平軸風力發電機
翼緣擴散外罩
計算流體力學
風洞實驗
關鍵字(英) Horizontal-axis wind turbine
Flanged diffuser
CFD
Wind tunnel test
第三語言關鍵字
學科別分類
中文摘要
本研究探討具翼緣擴散外罩及扭轉葉片對小型水平軸風力發電機之空氣動力特性影響,首先,以數值模擬軟體FLUENT探討翼緣擴散外罩在流場中之效應,結果顯示在外罩內部有加速性,這是因擴散角度與翼緣長度成線性比例的關係。再來以風洞實驗有無外罩、有無扭轉角度葉片及在不同風速與不同葉片數(solidities)下進行實驗。本論文為研究翼緣擴散外罩以及扭轉效應對功率、扭力輸出和風力發電機轉子之旋轉速度在高速(10~20米/秒)的實驗。而翼緣擴散外罩入口直徑為30公分、長度為10公分、擴散角度為30度、翼緣長度為3公分以及扭轉35度之扭轉葉片。結果顯示,設計出前緣擴散外罩可顯著的提升功率輸出、扭力輸出、小型風力發電機轉子之旋轉速度以及功率係數可能超過貝茲限制。翼緣擴散效應對於轉子性能取決於solidity和風速,隨著solidity和風速越大,翼緣擴散效應的影響就越小。功率係數和扭力係數則隨著風速逐漸增加趨於一恆定值,而在solidity為35-40%時有最大之功率輸出。結果也顯示出在不同轉子中,大翼尖扭轉葉片有最高的功率輸出。
英文摘要
This thesis studies the aerodynamic characteristics of a small horizontal-axis wind turbine with twisted blades and a shrouded diffuser with flange. First, a numerical study is conducted using a FLUENT software to investigate the effects of flanged diffusers on flow characteristics. Results show that the flow is accelerated inside the diffuser, which is roughly, linearly proportional to the diffuser angle and the flange length. Second, wind tunnel tests are conducted without and with the flanged diffuser, without and with twisted blade angle, under different wind speeds and blade numbers (solidities). These experiments investigate the flanged diffuser and twisted effects on the power, torque outputs, and rotor rotating speed of wind turbines at high wind speeds (10 to 20 m/s). The flanged diffuser has an inlet diameter of 30 cm, a length of 10 cm, a diffusion angle of 30o and a flange length is 3 cm, and the twisted blade has 35o twisted angle. Results show that the designed flanged diffuser may significantly increase the power output, torque output and rotor rotating speed of the small-size wind turbine, and the power coefficients may exceed the Betz’ limit. The flanged diffuser effect on these rotor performances depends on the solidity and wind speed. The higher the solidity and the wind speed are, the smaller the flanged diffuser effect is. The power coefficient and torque coefficient for the rotor with the flanged diffuser gradually approach constant values as the wind speed increases. Solidities of 35-40% have the maximum power output. The results also show that the twisted, large-tip blade rotor has the highest power output among the tested rotors.
第三語言摘要
論文目次
誌  謝	I
中文摘要 II
英文摘要 III
圖片目錄	IX
表目錄	XIV
符號說明	XV
第一章 緒論	1
1-1 研究動機	1
1-2 文獻回顧	9
1-3 研究目的	11
第二章:實驗設備與量測儀器	12
2-1實驗設備	12
2-1-1 大型風洞	12
2-1-2小型風力發電機模型	13
2-2實驗測量儀器	13
2-2-1速度量測系統	13
2-2-2扭力量測系統	14
2-2-3轉速計	14
2-2-4量測顯示與控制系統	14
2-2-5大氣狀態量測裝置	14
第三章 研究方法	19
3-1 數值方法	19
3-1-1數值模擬流程	19
3-2 風洞系統實驗方法	21
3-2-1風洞系統實驗流程	21
第四章 實驗結果與討論	27
4-1外罩效率之數值模擬	27
4-1-1擴散角度	27
4-1-2翼緣長度	29
4-1-3數值模擬結果	32
4-2 小型風力發電機空氣動力特性之實驗	42
4-2-1擴散外罩之增益效應	42
4-2-2數值與實驗比較	43
4-3葉片之扭轉角度	48
第五章 結論	73
5-1 外罩之影響	73
5-2扭轉葉片之影響	74
第六章 未來展望	76
參考文獻	77
附錄 81

圖片目錄
圖1-1 水平軸式風力發電機[2]	6
圖1-2 水平軸式風力機之構造圖[3]	7
圖1-3 垂直軸式風力發電機表[2]	7
圖2-1 大型風洞	15
圖2-2 裝設NACA4415型葉片的風力發電機模型	15
圖2-3 皮托管	16
圖2-4 橫向與縱向之位移平台	16
圖2-5  速度、扭力、轉速量測系統	17
圖2-6 量測顯示與控制系統	17
圖2-7 大氣狀態量測裝置	18
圖3-1-1 此為二維流場中模擬外罩之網格圖	20
圖3-1-2 CFD求解流程圖	24
圖3-2-1 具外罩效率實驗流程圖	25
圖3-2-2 小型風力發電機效率實驗流程圖	26
圖4-1 擴散外罩示意圖	33
圖4-2 在10米/秒下不同擴散角度之速度增益圖	33
圖4-3 在X/D為0.1、0.3下不同擴散角度下之速度增益圖	34
圖4-4(A) 為固定外罩平板之擴散角度為0度	34
圖4-4(B) 為固定外罩平板之擴散角度為30度	35
圖4-4(C) 為固定外罩平板之擴散角度為50度	35
圖4-5 為固定外罩擴散角度為0度,距入口5CM處的速度增益圖	.36
圖4-6 為固定外罩擴散角度為20度,距入口5CM處速度增益圖	...36
圖4-7(A) 擴散角度為0度時,H/D=0.05之速度分布圖	37
圖4-7(B) 擴散角度為0度時,H/D=0.15之速度分布圖	37
圖4-7(C) 擴散角度為0度時,H/D=0.25之速度分布圖	38
圖4-8 分別在擴散角度為0°、20°下,X/D為0.1、0.3時之速度增益圖	38
圖4-9 NACA4415翼型外罩在不同擴散角度的速度分布圖	39
圖4-10 NACA4415翼型外罩在X/D為0.1、0.3下不同擴散角度下之速度增益圖	39
圖4-11(A) NACA4415翼型外罩在10米/秒、擴散角度10度時流場速度分布圖	40
圖4-11(B) NACA4415翼型外罩在10米/秒、擴散角度20度時流場速度分布圖	40
圖4-11(C) NACA4415翼型外罩在10米/秒、擴散角度30度時流場速度分布圖	41
圖4-12 在10米/秒下擴散角度30度有無FLANGE之比較圖	41
圖4-13 數值模擬在自由流10米/秒、擴散角度30度時速度分布圖	42
圖4-14 外罩示意圖	44
圖4-15 在垂直方向上不同速度下入口處之分布圖	44
圖4-16 在垂直方向上不同速度下距5公分處之分布圖	45
圖4-17 在垂直方向上不同速度下出口處之分布圖	45
圖4-18 在水平方向上不同速度下距入口8公分處之分布圖	46
圖4-19 在水平方向上不同速度下距出口處4.5公分之分布圖	46
圖4-20 在10米/秒、擴散角度30度時,數值模擬與實驗數值在距入口處8公分處的速度比較圖	47
圖4-21 在10米/秒、擴散角度30度時,數值模擬與實驗數值在距外罩出口4.5公分處之速度比較圖	47
圖4-22 NACA4415之示意圖	56
圖4-23 在12米/秒下不同扭轉葉片之CP-TSR圖	56
圖4-24 在12米/秒下不同扭轉葉片之TORQUE-RPM圖	57
圖4-25 在不同風速下40度大翼尖6葉片之POWER-RPM圖	57
圖4-26 在不同風速下40度大翼尖6葉片之CP-TSR圖	58
圖4-27 在不同風速下40度大翼尖6葉片之TORQUE-RPM圖	58
圖4-28  在12米/秒下具外罩40度大翼尖6葉片在不同位置之POWER-RPM圖	59
圖4-29 在12米/秒下40度大翼尖6葉片有無外罩之POWER-RPM圖	59
圖4-30 在14米/秒下40度大翼尖6葉片有無外罩之POWER-RPM圖	60
圖4-31 在不同風速下具外罩6葉片之POWER-RPM圖	60
圖4-32 在不同風速下具外罩6葉片之CP-TSR圖	61
圖4-33 在不同風速下具外罩6葉片之TORQUE-RPM圖	61
圖4-34 不同大小格網示意圖,左:1.3公分*1.3公分,右:0.65公分*0.65公分	62
圖4-35 具外罩在14米/秒下40度大翼尖不同網子之POWER-RPM 圖	62
圖4-36 在12米/秒下不同葉片數之POWER-RPM圖	63
圖4-37 在12米/秒下不同葉片之POWER-RPM圖	63
圖4-38 在不同風速下無外罩12葉片之POWER-RPM圖	64
圖4-39 在不同風速下無外罩12葉片之TORQUE-RPM圖	64
圖4-40 在不同風速下具外罩12葉片之POWER-RPM圖	65
圖4-41 在不同風速下具外罩12葉片之TORQUE-RPM圖	65
圖4-42 在不同風速下無外罩6葉片與發電機之匹配圖	66
圖4-43 在不同風速下具外罩6葉片與發電機之匹配圖	66
圖4-44 在不同風速下無外罩12葉片與發電機之匹配圖	67
圖4-45 在不同風速下具外罩12葉片與發電機之匹配圖	67
圖4-46 四葉片示意圖	68
圖4-47 六葉片示意圖	68
圖4-48 七葉片示意圖	69
圖4-49 八葉片示意圖	69
圖4-50  九葉片示意圖	70
圖4-51 十二葉片示意圖	70

表目錄
表1-1 世界風能報告[1] 8
表4-1 各類葉片之起動風速表 71
表4-2 無外罩6葉片與12葉片性能參數比較 72
表4-3 具外罩6葉片與12葉片性能參數比較 72
參考文獻
[1]  世界風能協會,Available at: http://www.wwindea.org/technology/ch01/estructura-en.htm.
[2]  Wikipedia,Wind turbine.Available at: http://en.wikipedia.org/wiki/Wind_turbine.
[3]  能源效率與再生能源網,Available at: http://www1.eere.energy.gov/windandhydro/wind_how.html
[4]  HowStuffWorks How Wind Power Works. Available at: http://science.howstuffworks.com/environmental/green-science/wind-power.htm.
[5]  M. M. Duquette, K. D. Visser, “Numerical implications of solidity and blade number on rotor performance of horizontal-Axis wind turbines”, Journal of Solar Energy Engineering , Vol.125, 2003, pp.425-432.
[6]  羅際航,2006,具不同翼型葉片的水平式風力機之數值模擬,碩士論文,台北:國立台灣科技大學機械工程學系。
[7]  T. Matsushima, S. Takagi, S. Muroyama, “Characteristics of a highly efficient propeller type small wind turbine with a diffuser”, Renewable Energy, Vol.31,  2006, pp.1343-1354.
[8]  K.I. Abe, M. Nishida, A. Sakurai, Y. Ohya, H. Kihara, E. Wada, K. Sato, “Experimental and numerical investigations of flow fields behind a small wind turbine with a flanged diffuser”, Journal of Wind Engineering and Industrial Aerodynamics , Vol.93, 2005, pp.951-970.
[9]  B.Frankovic, and I.Vrsalovic, “New High Profitable Wind Turbines,” Renewable Energy, Vol. 24, 2001, pp.491-499.
[10] F.Bet, H.Grassmann, “Upgrading conventional wind turbines”, Renewable Energy , Vol.28, 2003, pp.71-78.
[11]  H.Grassmann,F.Bet, G. Cabras, M. Ceschia, D. Cobai, “A partially static turbine-first experimental results”, Renewable Energy,Vol. 28,  2003, pp.1779-1785.
[12] S.Y.Hu, J.H.Cheng, “Innovatory designs for ducted wind turbines”, Renewable Energy ,Vol.33,  2008, pp.1491-1498.
[13] Y.Ohya,T. Karasudani,A. Sakurai,K.I. Abe,M. Inoue, “Development of a shrouded wind turbine with a flanged diffuser”, Journal of Wind Engineering and Industrial Aerodynamics,Vol.96, 2008, pp.524-539.
[14] F. Wang, L. Bai, J. Fletcher, J. Whiteford, D. Cullen, “The methodology for aerodynamic study on a small domestic wind turbine with scoop”, Journal of Wind Engineering and Industrial Aerodynamics , Vol.96 , 2008, pp.1-24.
[15] K. Abe, Y. Ohya, “An investigation of flow fields around flanged diffusers using CFD“, Journal of Wind Engineering and Industrial Aerodynamics , Vol.92,  2004, pp.315-330. 
[16] O.Igra, “ Research and development for shrouded wind turbines“, Energy. Conv. Manage, Vol.21, 1981, pp.13-48. 
[17] B.L.Gilbert, K.M.Foreman, “Experiment with a diffuser-augmented model wind turbine“,Trans. ASME, J. Energy Resour,Technol., Vol.105, 1983, pp.46-53.
[18] 劉立仁,2010,小型水平軸式風力發電機空氣動力特性探討,碩士論文,淡水:淡江大學航空太空工程學系碩士班。
[19] K.Abe, H.Kihara, A. Sakurai, M.Nishida, Y.Ohya, E.Wada, K.Sato, “An experimental study of tip-vortex structures behind a small wind turbine with a flanged diffuser“, Wind Struct., Vol.9, 2006, pp.413-417. 
[20] B.L.Gilbert, R.A.Oman, K.M.Foreman, “Fluid dynamics of diffuser-augmented wind turbines“, J. Energy ,Vol.2, 1978, pp. 368-374. 
[21] A.Betz, “Introduction to the Theory of Flow Machines“, (D. G. Randall, Trans.), 1st ed, 1966, pp.236-237. Oxford: Pergamon Press.
[22] 陳國忠,2005,葉片扭轉角對水平式風力機性能影響之數值研究,碩士論文,台北: 國立台灣科技大學機械工程學系。
[23] 蔡孟杰,2004,外罩式多頁風力渦輪機之研究,碩士論文,台南:國立成功大學航空太空工程學系碩博士班。
[24] 簡名硯,2011,小型水平軸式風力發電系統之研製,碩士論文,淡水:淡江大學航空太空工程學系碩士班。
[25] 瑞領科技股份有限公司,LW-3840大型風洞使用手冊。
[26] U.K. Saha, M. Jaya Rajkumar, “On the performance analysis of Savonius rotor with twisted blades“, Renewable Energy, Vol 31, 2006, pp.1776-1788。
論文全文使用權限
校內
紙本論文於授權書繳交後2年公開
同意電子論文全文授權校園內公開
校內電子論文於授權書繳交後2年公開
校外
同意授權
校外電子論文於授權書繳交後2年公開

如有問題,歡迎洽詢!
圖書館數位資訊組 (02)2621-5656 轉 2487 或 來信